NO.163 Read the question, and then refer to the exhibit.
<Switch-A>display interface Ten-GigabitEthernet 1/0/1 Ten-GigabitEthernet1/0/1 Current state: Administratively DOWN Line protocol state: DOWN IP packet frame type: Ethernet II, hardware address: d894-03fb-793d Description: Ten-GigabitEthernet1/0/1 Interface Bandwidth: 10000000 kbps Loopback is not set Media type is stack wire, port hardware type is STACK_SFP_PLUS Unknown-speed mode, unknown-duplex mode Link speed type is autonegotiation, link duplex type is autonegotiation Flow-control is not enabled Maximum frame length: 10000 Allow jumbo frames to pass Broadcast max-ratio: 100% Multicast max-ratio: 100% Unicast max-ratio: 100% PVID: 1 MDI type: Automdix Port link-type: Trunk VLAN Passing: 10, 20 VLAN permitted: 10, 20 Trunk port encapsulation: IEEE 802.1q Port priority: 0 Last link flapping: 0 hours 0 minutes 18 seconds Last clearing of counters: Never Peak input rate: 78 bytes/sec, at 2011-03-31 04:55:57 Peak output rate: 15 bytes/sec, at 2011-03-30 23:00:57 Last 300 second input: 0 packets/sec 67 bytes/sec – % Last 300 second output: 0 packets/sec 14 bytes/sec – % Input (total): 62670 packets, 8565340 bytes 0 unicasts, 0 broadcasts, 62670 multicasts, 0 pauses Input (normal): 62670 packets, – bytes 0 unicasts, 0 broadcasts, 62670 multicasts, 0 pauses Input: 0 input errors, 0 runts, 0 giants, 0 throttles 0 CRC, 0 frame, – overruns, 0 aborts – ignored, – parity errors Output (total): 3707 packets, 1294835 bytes 0 unicasts, 0 broadcasts, 3707 multicasts, 0 pauses Output (normal): 3707 packets, – bytes 0 unicasts, 0 broadcasts, 3707 multicasts, 0 pauses Output: 0 output errors, – underruns, – buffer failures 0 aborts, 0 deferred, 0 collisions, 0 late collisions 0 lost carrier, – no carrier
A customer added a new switch to their network. They connected it using interface Ten-GigabitEthernet 1/0/1. They are using VLAN 10 and 20 for the devices in their network.
The new switch was fully operational. Then, the customer experienced a power failure later that day and could not reach any device on the new switch after the power returned.
From the output in the exhibit, would could be the issue?

NO.164 Place the components on the left in the correct order on the right for the recommended power-up sequence.

NO.165 HPE support asks you to provide the Active Health System log from HPE StoreEasy 1660 Storage to expedite a troubleshooting process.
Which procedures will generate the AHS log for HPE Support? (Choose two.)

NO.166 You are installing a DL385 GEN10 LFF server at a customer site. The customer has a P8i6i-a RAID controller in the host After installing the provided 8 LFF disks in the front drive Days, you realize that the order also included two more SFF drives for the OS to boot from, but there are no SFF drive slots in the server, because it shipped from the factory.
Which action must be performed to finish the installation?

NO.167 A customer needs to increase the availability and bandwidth of network connectivity to their servers.
Which switch feature meets the customer’s needs?

NO.168 Exhibit:

Which HPE ProLiant Server meets the customer’s requirements?

Which HPE ProLiant Server meets the customer’s requirements?

NO.169 You need to change BIOS configuration settings without rebooting a server.
Which system utility should you use?

NO.170 Match each HPE solution to its optimal use case.

NO.171 Refer to the exhibit.

A customer has been using VEEAM and the HPE StoreOnce 3620 shown in the exhibit to backup their environment. The customer’s legal team has asked to double their retention times for all backup sets, and they are starting to run out of space on the StoreOnce.
Which options could you recommend that the customer add to their existing configuration to accommodate the new requirement? (Select two. Each option represents a separate solution.)

NO.172 A customer needs to consolidate software, hardware, and backup in a single integrated solution to reduce the cost and complexity of their IT environment Which solution meets the customer needs?

NO.173 A customer has a new virtual environment. They selected HPE servers for the environment in order to achieve better performance for their applications.
Which HPE feature enables the customer to achieve this server performance improvement?

NO.174 You have configured a port on an HPE FlexFabric 5900 series switch that is connected to a VMware ESXi server to support multiple VLANs.

Given the configuration above, what should happen to any of the untagged traffic coming from the VMware ESXi host?

NO.175 Why is SNMPv2c considered to be insecure?

NO.176 A customer needs a storage solution to host a new virtualization platform that will host a database application. The customer is considering an HPE Nimble array.
What features would lead you to propose an HPE Nimble array over an HPE 3PAR array? (Select two.)

NO.177 Refer to the exhibit.

You are designing a new Nimble AF40 for your customer. The array will be added into an existing Nimble HF60 environment connected with SN6000B switches. You have created the configuration shown in the exhibit and noticed an error.
What should you change in your configuration to ensure it meets the customer requirements?