300-710 – Prepaway Exam Dumps

Q13. An engineer is setting up a new Firepower deployment and is looking at the default FMC policies to start the implementation During the initial trial phase, the organization wants to test some common Snort rules while still allowing the majority of network traffic to pass Which default policy should be used?

Maximum Detection

Security Over Connectivity

Balanced Security and Connectivity

Connectivity Over Security
https://www.cisco.com/c/en/us/td/docs/security/firepower/623/fdm/fptd-fdm-config-guide-623/fptd-fdm-intrusion.html

Q14. An engineer is troubleshooting connectivity to the DNS servers from hosts behind a new Cisco FTD device. The hosts cannot send DNS queries to servers in the DMZ. Which action should the engineer take to troubleshoot this issue using the real DNS packets?

Use the Connection Events dashboard to check the block reason and adjust the inspection policy as needed.

Use the packet capture tool to check where the traffic is being blocked and adjust the access control or intrusion policy as needed.

Use the packet tracer tool to determine at which hop the packet is being dropped.

Use the show blocks command in the Threat Defense CLI tool and create a policy to allow the blocked traffic.

Q15. A network administrator notices that remote access VPN users are not reachable from inside the network. It is determined that routing is configured correctly, however return traffic is entering the firewall but not leaving it What is the reason for this issue?

A manual NAT exemption rule does not exist at the top of the NAT table.

An external NAT IP address is not configured.

An external NAT IP address is configured to match the wrong interface.

An object NAT exemption rule does not exist at the top of the NAT table.

Q16. An engineer must investigate a connectivity issue from an endpoint behind a Cisco FTD device and a public DNS server. The endpoint cannot perform name resolution queries. Which action must the engineer perform to troubleshoot the issue by simulating real DNS traffic on the Cisco FTD while verifying the Snarl verdict?

Perform a Snort engine capture using tcpdump from the FTD CLI.

Use the Capture w/Trace wizard in Cisco FMC.

Create a Custom Workflow in Cisco FMC.

Run me system support firewall-engine-debug command from me FTD CLI.

Explanation
The Capture w/Trace wizard in Cisco FMC allows you to capture packets on an FTD device and trace their path through the Snort engine. This can help you troubleshoot connectivity issues from an endpoint behind an FTD device and a public DNS server, as well as verify the Snort verdict for the DNS traffic. The Capture w/Trace wizard lets you specify the source and destination IP addresses, ports, and protocols for the packets you want to capture and trace, as well as the FTD device and interface where you want to perform the capture.
You can also apply filters to limit the capture size and duration. After you start the capture, you can ping the DNS server from the endpoint and then view the captured packets and their Snort verdicts in the FMC web interface2.
To use the Capture w/Trace wizard in Cisco FMC, you need to follow these steps2:
In the FMC web interface, navigate to Troubleshooting > Capture/Trace.
Click New Capture.
Choose an FTD device from the Device drop-down list.
Choose an interface from the Interface drop-down list.
Enter the source and destination IP addresses, ports, and protocols for the packets you want to capture and trace. For example, if you want to capture DNS queries from an endpoint with IP address 10.1.1.100 to a DNS server with IP address 8.8.8.8, you can enter these values:
Source IP: 10.1.1.100
Source Port: any
Destination IP: 8.8.8.8
Destination Port: 53
Protocol: UDP
Optionally, apply filters to limit the capture size and duration. For example, you can set the maximum number of packets to capture, the maximum capture file size, or the maximum capture time.
Click Start.
Ping the DNS server from the endpoint and wait for some packets to be captured.
Click Stop to stop the capture.
Click View Capture to see the captured packets and their Snort verdicts.
The other options are incorrect because:
Performing a Snort engine capture using tcpdump from the FTD CLI will not allow you to trace the path of the packets through the Snort engine or verify their Snort verdicts. Tcpdump is a command-line tool that can capture packets on an FTD device, but it does not provide any information about how Snort processes those packets or what actions Snort takes on them2.
Creating a Custom Workflow in Cisco FMC will not help you troubleshoot a connectivity issue from an endpoint behind an FTD device and a public DNS server. A Custom Workflow is a user-defined set of pages that display event data in different formats, such as tables, charts, maps, and so on. A Custom Workflow does not allow you to capture or trace packets on an FTD device3.
Running the system support firewall-engine-debug command from the FTD CLI will not allow you to simulate real DNS traffic on the FTD device or verify the Snort verdict for that traffic. The firewall-engine-debug command is a diagnostic tool that can generate synthetic packets and send them through the Snort engine on an FTD device. The synthetic packets are not real network traffic and do not affect any connections or policies on the FTD device4.

Q17. With Cisco FTD integrated routing and bridging, which interface does the bridge group use to communicate with a routed interface?

switch virtual

bridge group member

bridge virtual

subinterface

Q18. Which two OSPF routing features are configured in Cisco FMC and propagated to Cisco FTD? (Choose two.)

OSPFv2 with IPv6 capabilities

virtual links

SHA authentication to OSPF packets

area boundary router type 1 LSA filtering

MD5 authentication to OSPF packets

Q19. An engineer is configuring a cisco FTD appliance in IPS-only mode and needs to utilize fail-to-wire interfaces. Which interface mode should be used to meet these requirements?

transparent

routed

passive

inline set

Q20. An engineer runs the command restore remote-manager-backup location 2.2.2.2 admin /Volume/home/admin FTD408566513.zip on a Cisco FMC. After connecting to the repository, the Cisco FTD device is unable to accept the backup file. What is the reason for this failure?

The backup file is not in .cfg format.

The wrong IP address is used.

The backup file extension was changed from .tar to .zip.

The directory location is incorrect.

Q21. Which Cisco Firepower rule action displays an HTTP warning page?

Monitor

Block

Interactive Block

Allow with Warning

Q22. Network users are experiencing Intermittent issues with internet access. An engineer ident med mat the issue Is being caused by NAT exhaustion. How must the engineer change the dynamic NAT configuration to provide internet access for more users without running out of resources?

Define an additional static NAT for the network object in use.

Configure fallthrough to interface PAT on ‘he Advanced tab.

Convert the dynamic auto NAT rule to dynamic manual NAT.

Add an identity NAT rule to handle the overflow of users.

Q23. A Cisco FTD device is running in transparent firewall mode with a VTEP bridge group member ingress interface What must be considered by an engineer tasked with specifying a destination MAC address for a packet trace?

The destination MAC address is optional if a VLAN ID value is entered

Only the UDP packet type is supported

The output format option for the packet logs unavailable

The VLAN ID and destination MAC address are optional

Q24. Which group within Cisco does the Threat Response team use for threat analysis and research?

Cisco Deep Analytics

OpenDNS Group

Cisco Network Response

Cisco Talos

Q25. An organization has noticed that malware was downloaded from a website that does not currently have a known bad reputation. How will this issue be addresses globally in the quickest way possible and with the least amount of impact?

by denying outbound web access

Cisco Talos will automatically update the policies.

by Isolating the endpoint

by creating a URL object in the policy to block the website

Q26. An engineer is troubleshooting a file that is being blocked by a Cisco FTD device on the network.
The user is reporting that the file is not malicious.
Which action does the engineer take to identify the file and validate whether or not it is malicious?

identify the file in the intrusion events and submit it to Threat Grid for analysis.

Use FMC file analysis to look for the file and select Analyze to determine its disposition.

Use the context explorer to find the file and download it to the local machine for investigation.

Right click the connection event and send the file to AMP for Endpoints to see if the hash is malicious.

Q27. An engineer is tasked with deploying an internal perimeter firewall that will support multiple DMZs Each DMZ has a unique private IP subnet range. How is this requirement satisfied?

Deploy the firewall in transparent mode with access control policies.

Deploy the firewall in routed mode with access control policies.

Deploy the firewall in routed mode with NAT configured.

Deploy the firewall in transparent mode with NAT configured.

Q28. An engineer must define a URL object on Cisco FMC. What is the correct method to specify the URL without performing SSL inspection?

Use Subject Common Name value.

Specify all subdomains in the object group.

Specify the protocol in the object.

Include all URLs from CRL Distribution Points.

Q29. An engineer wants to perform a packet capture on the Cisco FTD to confirm that the host using IP address 192
168.100.100 has the MAC address of 0042 7734.103 to help troubleshoot a connectivity issue What is the correct tcpdump command syntax to ensure that the MAC address appears in the packet capture output?

-nm src 192.168.100.100

-ne src 192.168.100.100

-w capture.pcap -s 1518 host 192.168.100.100 mac

-w capture.pcap -s 1518 host 192.168.100.100 ether

Q30. A network administrator is reviewing a monthly advanced malware risk report and notices a host that Is listed as CnC Connected. Where must the administrator look within Cisco FMC to further determine if this host is infected with malware?

Analysis > Hosts > indications of Compromise

Analysts > Files > Malware Events

Analysis > Hosts > Host Attributes

Analysis > Flies > Network File Trajectory

Explanation
To determine if a host is infected with malware, the network administrator can look at the Indications of Compromise (IOC) feature in Cisco FMC. The IOC feature analyzes network and endpoint data collected by Firepower sensors and AMP for Endpoints connectors, and identifies hosts that exhibit signs of compromise or infection. The IOC feature uses predefined rules based on Cisco Talos intelligence and other sources to detect IOCs on hosts. One of these rules is CnC Connected, which indicates that a host has communicated with a command-and-control (CnC) server that is known to be associated with malware activity2.
To view the IOC information for a host, the network administrator can navigate to Analysis > Hosts > Indications of Compromise in Cisco FMC, and select a host from the table. The IOC Details page will show the IOC events for that host, including the CnC Connected event, along with other information such as severity, timestamp, source, destination, protocol, and rule name. The network administrator can also view more details about each IOC event by clicking on it2.
The other options are incorrect because:
Analysis > Files > Malware Events shows information about files that have been detected as malware by Firepower sensors or AMP for Endpoints connectors. This does not show information about hosts that are infected with malware or have communicated with CnC servers3.
Analysis > Hosts > Host Attributes shows information about hosts that have been discovered by Firepower sensors, such as IP address, MAC address, operating system, applications, users, vulnerabilities, and so on. This does not show information about IOCs or CnC connections on hosts4.
Analysis > Files > Network File Trajectory shows information about files that have traversed your network and have been detected by Firepower sensors or AMP for Endpoints connectors. This allows you to track where a file came from, where it went, and what happened to it along the way. This does not show information about hosts that are infected with malware or have communicated with CnC servers5.

Q31. Which two conditions must be met to enable high availability between two Cisco FTD devices? (Choose two.)

same flash memory size

same NTP configuration

same DHCP/PPoE configuration

same host name

same number of interfaces

Q32. How many report templates does the Cisco Firepower Management Center support?

20

10

5

unlimited

Q33. An engineer is configuring a second Cisco FMC as a standby device but is unable to register with the active unit. What is causing this issue?

The primary FMC currently has devices connected to it.

The code versions running on the Cisco FMC devices are different

The licensing purchased does not include high availability

There is only 10 Mbps of bandwidth between the two devices.
https://www.cisco.com/c/en/us/td/docs/security/firepower/620/configuration/guide/fpmc-config-guide-v62/firepower_management_center_high_availability.html

Q34. An engineer is monitoring network traffic from their sales and product development departments, which are on two separate networks What must be configured in order to maintain data privacy for both departments?

Use a dedicated IPS inline set for each department to maintain traffic separation

Use 802 1Q mime set Trunk interfaces with VLANs to maintain logical traffic separation

Use passive IDS ports for both departments

Use one pair of inline set in TAP mode for both departments

Q35. An administrator is setting up Cisco Firepower to send data to the Cisco Stealthwatch appliances. The NetFlow_Set_Parameters object is already created, but NetFlow is not being sent to the flow collector. What must be done to prevent this from occurring?

Add the NetFlow_Send_Destination object to the configuration

Create a Security Intelligence object to send the data to Cisco Stealthwatch

Create a service identifier to enable the NetFlow service

Add the NetFlow_Add_Destination object to the configuration

Q36. The event dashboard within the Cisco FMC has been inundated with low priority intrusion drop events, which are overshadowing high priority events. An engineer has been tasked with reviewing the policies and reducing the low priority events. Which action should be configured to accomplish this task?

generate events

drop packet

drop connection

drop and generate

Q37. A network security engineer must export packet captures from the Cisco FMC web browser while troubleshooting an issue. When navigating to the address Error! Hyperlink reference not valid. IP>/capture/CAPI/pcap/test.pcap. an error 403: Forbidden is given instead of the PCAP file. Which action must the engineer take to resolve this issue?

Disable the HTTPS server and use HTTP instead.

Enable the HTTPS server for the device platform policy.

Disable the proxy setting on the browser.

Use the Cisco FTD IP address as the proxy server setting on the browser.

Prepaway Exam Dumps

Category: 300-710

2024 New 300-710 Exam Questions Real Cisco Dumps [Q13-Q37]

Category Archives: 300-710