NACE-CIP2-001 Actual test answers – Prepaway Exam Dumps

(PDF) CIP Level 2 NACE-CIP2-001 Exam and Certification Test Engine

Use NACE-CIP2-001 Exam Dumps (2025 PDF Dumps) To Have Reliable NACE-CIP2-001 Test Engine

NO.47 An Inspection and Test Plan is required when:

It is always required

When the Coating Applicator requests one

When the Owner specifies one

When the Inspector requests one

NO.48 The solvent sensitivity/solvent wipe test (ASTM D4752) is used to determine the cure of

urethanes.

inorganic zincs.

epoxies.

powder coatings.

NO.49 A single component water borne acrylic coating cures by:

Solvent Evaporation

Coalescence

Co-Reaction

Oxidation

NO.50 Generally for safety considerations, waterjetting hose connections use

an oil/water separator.

a long wand.

a whip-lock device.

filters.

NO.51 NACE International Standards are developed by:

Government mandates

International mandates

Standard committees

Regional mandates

NO.52 You should bulk store coatings containing isocyanates

in a well ventilated area separate from the work place.

in a heated warehouse.

in a refrigerated warehouses

wherever it is convenient

NO.53 NACE No.13/ SSPC 6 identifies the use of:

Abrasive blasting only

Watterjetting only

Steam cleaning only

Various methods of cleaning

NO.54 Ideally, documentation requirements should be defined:

At the pre-job conference

In the specification

By the inspector

By the contractor

NO.55 You are the NACE Level 2 inspector reviewing the documentation from a NACE Level 1 you notice significant documentation errors.
Your FIRST preferred course of action is to:

Correct the errors yourself and suggest the Level 1 inspector be replaced

Correct the errors yourself and advise your supervisor that the Level 1 Inspector is incompetent

Have the Level 1 Inspector correct the errors and set up remedial training to improve the quality of documentation

Correct the errors yourself and submit the reports without any further action

NO.56 When performing testing in accordance with ASTM D 2583 the inspector may observe:

Adhesion failure

Cohesion failure

Glue failure

Cold flow or creep

NO.57 When observing design defects the NACE Inspector should:

Document the defect and the potential problems that could result

Ignore the defect as the inspector can’t change the design

Request that the item be rebuilt with a better design for coating

Stop the job immediately

NO.58 Coating Surveys are legally required:

On commercial marine vessels and offshore platforms

On high pressure gas lines and fireproofed structures

On water tanks and potable water pipelines

On food and beverage vessels and can linings

NO.59 When working with someone who is very concerned about Stability and maintaining adherence to the status-quo, the Inspector should try to:

Implement immediate to get them motivated

Give them as much advance notice as possible about upcoming changes

Challenge their value to the team and try to get them out of their comfort zone

Make sure they are the center of attention in all site meetings

NO.60 NACE Standards include:

Standard Practices

Material Requirements

a) & b)

a) only

NO.61 The HATE adhesion tester uses

compressed air to apply pressure to the test dolly.

mechanical means only to apply pressure to the test dolly.

a special tape to apply pressure to the test dolly.

a hydraulic piston to apply pressure to the test dolly.

NO.62 When observing fabrication defects the NACE Inspector should:

Require they be corrected prior to coating

Consult the specification to determine how they should be treated

Stop the job immediately

Write an NCR and call the fabricator

NO.63 When using a destructive Paint Inspection Gauge the NACE inspector must:

Determine the Dry Film Thickness of the coating prior to use

Ensure the glue on the dolly is properly applied prior to use

Consult SSPC Guide 1 prior to use

Select the appropriate hand wheel based on the measured Dry Film Thickness prior to us

NO.64 Which product, is used in conjunction with other coatings such as FBE when the lines run through wetlands or a body of water?

2-Layet Polyethylene (PE)

3-Layet Polyethylene (PE)

Concrete

Coal Tar Enamel

NO.65 The number of air turns in an enclosure can be affected by all of these EXCEPT

time of the year (winter/summer).

type of dehumidification equipment (refrigerant or desiccant).

manufacturer of the equipment.

coating type.

NO.66 In the event of a conflict between the Product Data Sheet and the Specification:

The Product Data Sheet prevails

The Specification prevails

It is up to the Inspector to decide which one to follow

It is up to the Applicator to decide which one to follow

NO.67 Dehumidification is defined as the removal of moisture vapor from the air to

provide worker comfort.

lower its temperature

raise its relative humidity.

lower its dew point,

NO.68 You are NACE Level 2 Inspector working on a tank lining job where a mobile centrifugal blast unit is being used to blast the tank floor to a NACE No.1/SSPC SP 5. The Contractor has completed his final blast and has called for a hold point inspection. This is the 1 st time you have seen field based centrifugal blast cleaning. You observe what appears to be staining on the substrate however the Contractor assures you this is normal when using centrifugal blast units and what you are seeing is what is defined in the standard as an acceptable variation in appearance.
Your FIRST preferred course of action is to:

Request that the Contractor re-blast the floor

Review the standard with the Contractor and re-inspect the floor

Shut the job down

Call your supervisor

NO.69 The standards defining surface cleanliness achieved by centrifugal blast cleaning are:

Different than air blast cleaning

The same as air blast cleaning

Slightly different to air blast cleaning

Comparable to air blast cleaning

NO.70 The cost of qualified Coating Inspection is normally offset by:

Lower Application Costs

Lower Coating Life Cycle Costs

Lower Safety Enforcement Costs

Lower Supervision Costs

Loading …

NACE-CIP2-001 (Coating Inspector Level 2) Certification Exam is a globally recognized certification offered by the National Association of Corrosion Engineers (NACE). Coating Inspector Level 2 certification is designed for individuals who have experience in the coatings industry and want to demonstrate their knowledge and expertise in coating inspection. NACE-CIP2-001 exam covers a wide range of topics related to coatings, including surface preparation, coating application, inspection techniques, and quality control.

NACE-CIP2-001 Dumps Full Questions with Free PDF Questions to Pass: https://www.prepawayexam.com/NACE/braindumps.NACE-CIP2-001.ete.file.html

Prepaway Exam Dumps

Tag: NACE-CIP2-001 Actual test answers

CIP Level 2 NACE-CIP2-001 Exam Dumps and Certification Test Engine [Q47-Q70]

Tag Archives: NACE-CIP2-001 Actual test answers